Keilton 120V AC Dusk to Dawn Photocell Light Sensor, Outdoor Hard-Wired
Product Description
Keilton 120V AC Dusk to Dawn Photocell Light Sensor, Outdoor Hard-Wired
- Automatic Dusk to Dawn Control – Built-in photocell sensor automatically turns lights ON at dusk and OFF at dawn, ensuring hands-free operation and energy savings
- Durable & Safe – ETL Listed lighting control standard and FCC PART 15, Class B compliant; rated for 50,000 hours lifespan with a 5-year warranty for reliable performance
- Electrical Rating – Input: 120V AC, 50/60Hz; Maximum Load: 100W incandescent, 55W fluorescent, 55W LED driver; Ultra-low 0.5W power consumption
- Easy Installation – Mounts in a 3/8-inch hole (M9x1.0 pipe thread) and hard-wires directly to your fixture. Wiring: Black = Line, White = Neutral, Red = Load
- Wide Application – Designed for installation inside weatherproof outdoor fixtures, including wall packs, driveway and walkway lights, post lamps, pole lanterns, and entryway porch lights
SPECIFICATIONS:
Rated voltage: 120V AC, 50/60Hz
Max. load: 1000W incandescent, 55W fluorescent, 55W LED driver Power consumption: 0.5W
On/Off level: 30Lux ON, 200Lux OFF
Working temperature: -30 °F~122 °F
Working humidity: 5%~95%RH
Overall dimensions(LxWxH): 1.6" x 0.77" x 1.46"
Leads length: 100mm (AWG#18)
Lifespan: 50,000 hours
Applications: wall pack, driveway and walkway lighting, post lamp, pole lantern, entry way porch light and other residential or commercial applications
HOW TO INSTALL:
Step 1: Shut OFF the power at the breaker.
Step 2: Use a hole puncher to punch a Dia. 0.6" knockout on junction box if needed.
Step 3: Screw out the lock nut from the sensor.
Step 4: Let the sensor's eye go through the knockout then secure the sensor with the lock nut.
Step 5: Connect the wires according to the wire diagram, black to black (Line), white to white (Neutral), red to Load.
Tips:
When you decide where to install the sensor:
1, Do not face the photocell into the midday sun. If the photo control is installed on the south side of a building, face the photocell east or west or point the photo control down toward the ground. The best direction to face the photo control is north.
2, Do not face the photocell to artificial or relected light. Light from windows, signs, street lights, etc., will cause the photo control not to switch on or cause the light to cycle on and off at night.
HOW TO TEST:
Step 1: Turn ON the light power, then wait up to 5 minutes for the photocell to switch it OFF.
Step 2: Cover the photocell eye completely with black tape or other dack material to simulate night condition, the light should be switched OFF.
Technical Specifications
You might also like
Espen LED Driver, VEL12035120H-3-CA Constant Current, Max. 12W, 120V Input, High Power Factor with quick connector. (Same as VEL12035120H-3)
Pack of 2, Outdoor Hard-Wired Post Eye Light Control Electric Resistor Photocell Light Sensor, Dusk to Dawn Sensor, Convert Fixtures to Auto On at Night, LED HID CFL JL-103A
XtremeAmazing Pack of 2 Dusk to Dawn Outdoor Hard-Wired Post Eye Electric Resistor Photocell Light Control Sensor Button Switch LED HID CFL JL-103A
120 Volt Dusk to Dawn Photocell Photoeye Light Sensor Switch, Auto On/Off, Use with Fluorescent, Incandescent or LED Bulbs, Use in light posts and poles
J.LUMI YCA1030 Outdoor Hard-Wired Post Eye Light Control with Photocell Light Sensor, Photocell Sensor, Dusk to Dawn Light Sensor, Photocell for Outdoor Light, UL Listed
Woods 59408WD Outdoor Hard-Wired Post Eye Light Control with Photocell Light Sensor
Woods 59413 59413WD Outdoor Conduit Lighting Control With Photocell and Swivel Mount (Hardwired, Black)
Zerodis AC 120V Dusk to Dawn Sensor Photoelectric Switch Light Photocell Sensor Lighting Switch
Custom Accessories Shop Craft 37722 12" x 20" x 1/32" High Temperature Gasket Material
Intermatic K4121C 120-Volt Stem Mount Thermal Photocontrol